Raster-Stamp-Tab-AccXes-Configuration-Dialog-Box

Raster Stamp Tab (AccXes Configuration Dialog Box)

Raster Stamp Tab (AccXes Configuration Dialog Box)

Specifies the raster stamp printed during output for Xerox wide format printers.

Summary

The Raster Stamp tab controls the raster stamp printed on the output print.

You can load the printer with predefined raster stamps, which are identified by stamp
names. You define stamp names for this driver by using the Edit Stamp Names dialog
box. The stamp names that you define should match the names that are defined in the
printer.

When you define a stamp name in the Edit Stamp Names dialog box, the name appears
in the Raster Stamp Selection drop-down list.

When you select a user-defined stamp name, fields on the Raster Stamp tab are enabled
that allow you to select stamp scaling, scaling type, and placement.

List of Options

The Raster Stamp tab contains the following options:

Raster Stamp Selection

Controls which raster stamp (if any) to be used on printed output.

No Raster Stamp

Overrides the printer raster stamp setting. No raster stamp is output.

Printer Default Stamp

Specifies that the printer defines the control for raster stamp output.

<Stamp name 1 – 8

Specifies the names that are defined through the Edit Stamp Names dialog box.

Edit Stamp Names

Opens the Edit Stamp Names dialog box, in which you can define raster stamp names
for the driver. The names should match those defined in the printer. Once defined,
the names are available on the Raster Stamp Selection drop-down list.

Scaling Factor

Specifies the output size of a loaded raster stamp. You can specify a scaling factor
of 10 through 999. The scaling factor can be either Relative to Drawing or Absolute.

Raster Stamp Placement

Controls the printed location of a raster stamp.

X Position

You can set the X position to Left, Center, Right, or Absolute in inches or millimeters.

Y Position

You can set the Y position to Top, Center, Bottom, or Absolute in inches or millimeters.

Rotation

You can set the rotation to 0, 90, 180, or 270 degrees.

Learning AutoCad

ecifies the raster stamp printed during output for Xerox wide format printers. Summary The Raster Stamp tab controls the raster stamp printed on the output …… 1 روز پیش دیدگاه‌ها برای AccXESConfigurationDialogBox بسته هستند … Options Tab (AccXES Configuration Dialog Box) · Raster Stamp Tab …dialog box is available by clicking the Edit Stamp Names button on the … AccXES Configuration Dialog Box · Raster Stamp Tab (AccXes Configuration …Accxes® Print Server Software Version 15.0 b 240 ….. Tool screen will display a message that the file was uploaded successfully and the stamp's.… Xerox FreeFlow Accxes System & Web Printer Management Tool Setup … Click on the [Connections] tab then the [LAN Settings] button. 3. … In the browser URL box, enter the http:// followed by your printer's IP … back a message stating either “Password verification passed” or “ ….. Raster Image Scale Mode.Raster Stamp Tab (AccXes Configuration Dialog Box) …Raster Stamp Tab (AccXes Configuration Dialog Box) …TABS OF THE CUSTOM PROPERTIES “CONFIGURATIONDIALOG .. ii Introduction. …. Printer • An XES Synergix 8825/8830 Printer with AccXES Controller and firmware …. Configure Port Displays either the Configure LPT Port dialog box or the …. Raster Stamp Selection – Click on the arrow of this drop- down menu to …box icon, AccXES, and the acronym XES are trademarks of XEROX ….. The Device Settings tab of the Printer Properties dialog contains a number of ….. The factory default setting for the Raster Stamp option is Printer Default.… Xerox 6204 With FreeFlow® Accxes® Print Server. D Size: 4 per minute ….. tab on the control panel from the default Ordinary Bond set- ting.