آموزش تصویری اتوکد دستورات دوبعدی و سه بعدی + ترفندهای اتوکد
ARC (Command)
Creates an arc.
To create an arc, you can specify combinations of center, endpoint, start point,
radius, angle, chord length, and direction values. Arcs are drawn in a counterclockwise
direction by default. Hold down the Ctrl key as you drag to draw in a clockwise direction.
The following prompts are displayed.
Start point
Draws an arc using three specified points on the arc’s circumference. The first point
is the start point (1).
or arc is used and you are immediately prompted to specify the endpoint of the new
arc. This creates an arc tangent to the last drawn line, arc, or polyline.
Center
Starts by specifying the center of the circle of which the arc is a part.
- Start point
-
Specify the start point of the arc.
- End point
-
Using the center point (2), draws an arc counterclockwise from the start point (1)
to an endpoint that falls on an imaginary ray drawn from the center point through
the third point (3).
The arc does not necessarily pass through this third point, as shown in the illustration.
- Angle
-
Draws an arc counterclockwise from the start point (1) using a center point (2) with
a specified included angle. If the angle is negative, a clockwise arc is drawn.
- Chord length
-
Draws either a minor or a major arc based on the distance of a straight line between
the start point and endpoint.If the chord length is positive, the minor arc is drawn counterclockwise from the
start point. If the chord length is negative, the major arc is drawn counterclockwise.
End
Starts by specifying the endpoint of the arc.
- Center point
-
Draws an arc counterclockwise from the start point (1) to an endpoint that falls on
an imaginary ray drawn from the center point (3) through the second point specified
(2).
- Angle
-
Draws an arc counterclockwise from the start point (1) to an endpoint (2), with a
specified included angle. If the angle is negative, a clockwise arc is drawn. - Included angle
-
Enter an angle in degrees or specify an angle by moving the pointing device counterclockwise.
- Direction
-
Begins the arc tangent to a specified direction. It creates any arc, major or minor,
clockwise or counterclockwise, beginning with the start point (1), and ending at an
endpoint (2). The direction is determined from the start point.
- Radius
-
Draws the minor arc counterclockwise from the start point (1) to the endpoint (2).
If the radius is negative, the major arc is drawn.
Center
Specifies the center of the circle of which the arc is a part.
- Start point
-
Specify start point of arc.
- End point
-
Draws an arc counterclockwise from the start point (2) to an endpoint that falls on
an imaginary ray drawn from the center point (1) through a specified point (3). - Angle
-
Draws an arc counterclockwise from the start point (2) using a center point (1) with
a specified included angle. If the angle is negative, a clockwise arc is drawn. - Chord length
-
Draws either a minor or a major arc based on the distance of a straight line between
the start point and endpoint.If the chord length is positive, the minor arc is drawn counterclockwise from the
start point. If the chord length is negative, the major arc is drawn counterclockwise.
Tangent to last line, arc, or polyline
Draws an arc tangent to the last line, arc, or polyline drawn when you press ENTER
at the first prompt.
- End point of arc
-
Specify a point (1).
create an arc, you can specify combinations of center, endpoint, start point, radius, angle, chord length, and direction values. … This creates an arc tangent to the last drawn line, arc, or polyline. … Draws an arc counterclockwise from the start point (1) using a center point (2 …Arc[ <Circle>, <Point M >, <Point N> ]: Returns the directed arc (counterclockwise ) of the given circle, with endpoints M and N. Arc[ <Ellipse>, <Point M>, <Point …6 Feb 201027 May 2016Arc command draws an arc with options for a center location, one end point, and a second end point or an angle.commands issued by anonymized users. We start to visualize the product …ARC command. On the toolbar, click on the DRAW ARC. Or with a text …… Keyboard: ARC.Ribbon: draw > arc > start point, center, endpoint. … Command: _arc, specify start point of arc or [Center]: // specify the start …command-line interface to Phabricator. Arcanists provides … A detailed command reference is available by running arc help. This document …arc tangent or perpendicular to one or two elements. The first point defines one end of the arc. If you place the first point on a key point of an element …